当前位置:首页 > 汽车电子 > 汽车电子
[导读]TI公司的drv8305-Q1是三相马达驱动的栅极驱动集成电路,提供三个高精度半桥驱动器,每个可驱动高边和低边N-MOSFET,电荷泵驱动器支持100%占空比,满足汽车应用的AEC-Q100规范,4.4V-45V工作电压,峰值栅极驱动电流1.25A和1A,主要用在三相BLDC和PMSM马达,汽车油泵和水泵,汽车风扇和鼓风机.本文介绍了DRV8305-Q1主要特性,框图,典型应用电路以及汽车两轴电动座椅驱动参考设计TIDA-01330主要特性,框图,电路图,材料清单和PCB设计图.DRV8305-Q1器件是一款面向三相马达驱动应用的栅极驱动器IC。该器件提供3个高精度半桥驱动器,每个均能驱动高边和低边N沟道MOSFET。电荷泵驱动器支持100%占空比和低压操作。该器件能够忍受高达45-V的负载突降电压。

 TI公司的drv8305-Q1是三相马达驱动的栅极驱动集成电路,提供三个高精度半桥驱动器,每个可驱动高边和低边N-MOSFET,电荷泵驱动器支持100%占空比,满足汽车应用的AEC-Q100规范,4.4V-45V工作电压,峰值栅极驱动电流1.25A和1A,主要用在三相BLDC和PMSM马达,汽车油泵和水泵,汽车风扇和鼓风机.本文介绍了DRV8305-Q1主要特性,框图,典型应用电路以及汽车两轴电动座椅驱动参考设计TIDA-01330主要特性,框图,电路图,材料清单和PCB设计图.DRV8305-Q1器件是一款面向三相马达驱动应用的栅极驱动器IC。该器件提供3个高精度半桥驱动器,每个均能驱动高边和低边N沟道MOSFET。电荷泵驱动器支持100%占空比和低压操作。该器件能够忍受高达45-V的负载突降电压。

The DRV8305-Q1 device is a gate driver IC for threephasemotor-drive applications. The device providesthree high-accuracy half-bridge drivers, each capableof driving a high-side and low-side N-channelMOSFET. A charge pump driver supports 100% dutycycle and low-voltage operation for cold cranksituations. The device can tolerate load dumpvoltages up to 45-V.

The DRV8305-Q1 device includes three bidirectionalcurrent-shunt amplifiers for accurate low-side currentmeasurements that support variable gain settings andan adjustable offset reference.

The DRV8305-Q1 device has an integrated voltageregulator to support an MCU or other system powerrequirements. The voltage regulator can be interfaceddirectly with a LIN physical interface to allow lowsystemstandby and sleep currents.

The gate driver uses automatic handshaking whenswitching to prevent current shoot through. The VDSof both the high-side and low-side MOSFETs isaccurately sensed to protect the external MOSFETsfrom overcurrent conditions. The SPI providesdetailed fault reporting, diagnostics, and deviceconfigurations such as gain options for the currentshunt amplifier, individual MOSFET overcurrentdetection, and gate-drive slew-rate control.

DRV8305-Q1主要特性:

1• AEC-Q100 Qualified for Automotive Applications

• Ambient Operating Temperature Ranges:

– Temperature Grade 0 (E): –40℃ to 150℃

– Temperature Grade 1 (Q): –40℃ to 125℃

• 4.4-V to 45-V Operating Voltage

• 1.25-A and 1-A Peak Gate Drive Currents

• Smart Gate Drive Architecture (IDRIVE &TDRIVE)

• Programmable High- and Low-Side Slew-RateControl

• Charge-Pump Gate Driver for 100% Duty Cycle

• Three Integrated Current-Shunt Amplifiers

• Integrated 50-mA LDO (3.3-V and 5-V Option)

• 3-PWM or 6-PWM Input Control up to 200 kHz

• Single PWM-Mode Commutation Capability

• Serial Peripheral Interface (SPI) for DeviceSettings and Fault Reporting

• Thermally-Enhanced 48-Pin HTQFP

• Protection Features:

– Fault Diagnostics and MCU Watchdog

– Programmable Dead-Time Control

– MOSFET Shoot-Through Prevention

– MOSFET VDS Overcurrent Monitors

– Gate-Driver Fault Detection

– Reverse Battery-Protection Support

– Limp Home-Mode Support

– Overtemperature Warning and Shutdown

DRV8305-Q1应用:

• Three-Phase BLDC and PMSM Motors

• Automotive Fuel and Water Pumps

• Automotive Fans and Blowers

图1.DRV8305-Q1框图

图2.DRV8305-Q1典型应用电路

汽车两轴电动座椅驱动参考设计TIDA-01330

The TIDA-01330 design implements the drive circuitsfor two independent brushed DC motors. It provides asolution for automotive power seats with a highlyintegratedtwo-axis driver, reducing the overall bill ofmaterials. The interface to a simple microcontrollerIllustrates how the design reduces the processingburden on the control software.

In addition to the drive circuit for two motors, this TIDesign also includes current feedback sense circuitsand other diagnostic features to ensure reliableoperation and detection of faults. Additionally thecontrol circuit for an LED illumination element isimplemented, as well as the feasibility of providingtactile feedback to the seat occupant by vibrating ineither axis.

参考设计TIDA-01330主要特性:

• Drives Two Independent Brushed DC Motors

• Up to 10-A Motor Current (Each Axis)

• Current Feedback on Each Axis

• Reverse Battery Protection

• Low-Pass Filtering on Battery Power

• Drives LED for Floor Illumination

• Simple Microcontroller Interface

• Reduced Bill of Materials

参考设计TIDA-01330应用:

• Power Seat Height and Forward and BackwardAdjustment

• Power Seat Back Recline Adjustment andPower Fold

• Other Two-Axis Brushed DC Motor Drives

图3.参考设计TIDA-01330外形图

参考设计TIDA-01330主要指标:

图4.参考设计TIDA-01330框图

图5.参考设计TIDA-01330扩展到五轴应用图

[!--empirenews.page--]

[!--empirenews.page--]

[!--empirenews.page--]

[!--empirenews.page--]

[!--empirenews.page--]

[!--empirenews.page--]

[!--empirenews.page--]

本站声明: 本文章由作者或相关机构授权发布,目的在于传递更多信息,并不代表本站赞同其观点,本站亦不保证或承诺内容真实性等。需要转载请联系该专栏作者,如若文章内容侵犯您的权益,请及时联系本站删除。
换一批
延伸阅读

参比电极是电化学研究和实际应用中不可或缺的组成部分,它在测量与控制电势方面发挥着关键作用。作为电化学电池的一个基本单元,参比电极的作用在于提供一个恒定且已知的电位基准,以便准确地确定工作电极(如氧化还原反应发生的部位)上...

关键字: 参比电极 电解液

随着汽车科技的不断发展,汽车空调作为提升驾驶舒适度的重要配置,已经成为现代汽车的标配。然而,在实际使用过程中,汽车空调不制冷的问题时有发生,给驾驶者和乘客带来不便。本文将深入探讨汽车空调不制冷的原因,并提出相应的解决策略...

关键字: 汽车空调 制冷剂

随着汽车电子技术的快速发展,LIN(Local Interconnect Network)总线技术作为一种低成本、简单的串行通信协议,在汽车内部网络中得到了广泛应用。LIN总线主要用于连接传感器和执行器等低速设备,实现与...

关键字: 汽车电子 串行通信协议 示波器

在汽车燃油系统中,碳罐电磁阀是一个至关重要的部件,它在控制挥发性燃油蒸汽排放及保持燃油经济性方面扮演着关键角色。碳罐电磁阀负责适时开启或关闭通向发动机进气歧管的通道,以实现燃油蒸汽的有效回收和燃烧。当碳罐电磁阀出现故障时...

关键字: 碳罐电磁阀 燃油系统

摩托车整流器是一个重要的电气组件,它主要的作用是将发电机发出的交流电转换为直流电,以便为摩托车的电气系统提供稳定的直流电源。

关键字: 摩托车 整流器

随着汽车工业的快速发展,空气流量传感器作为发动机管理系统的核心组件之一,其技术发展对于提高发动机性能、燃油经济性和排放控制至关重要。本文综述了空气流量传感器的发展历程、技术原理、分类以及最新进展,并探讨了未来可能的技术趋...

关键字: 传感器 发动机 汽车

激光雷达与微波雷达在原理上相似,都是利用电磁波进行目标探测和跟踪。它们都发射电磁波并接收反射信号,通过处理这些信号来获取目标的距离、速度和其他运动参数。然而,激光雷达使用激光作为载波,具有更高的分辨率和抗干扰能力,特别适...

关键字: 激光雷达 跟随定位

激光雷达(英文:Laser Radar ),是以发射激光束探测目标的位置、速度等特征量的雷达系统。激光雷达通过发射激光脉冲并接收从目标物体反射回来的光信号来工作。这些反射回来的信号被转换成电信号,并经过处理和分析,从而得...

关键字: 激光雷达 激光发射机

激光雷达(LiDAR,Light Detection and Ranging)是一种主动遥感技术,它通过向目标发射激光脉冲并测量反射回来的时间来探测和测量目标的距离、速度和其他特性。激光雷达系统广泛应用于许多领域,包括地...

关键字: 激光雷达

激光雷达(Laser Radar)是一种利用激光束探测目标位置、速度等特征量的雷达系统。其工作原理是向目标发射探测信号(激光束),然后将接收到的从目标反射回来的信号(目标回波)与发射信号进行比较,经过适当处理后,就可以获...

关键字: 激光雷达 雷达系统
关闭
关闭