S3C2440 测试程序(五) 触摸屏实验

电阻式触摸屏的检测原理是触摸后引起上下两个导电层的接触，改变了电压输出，进行A/D转换后成了该点的X,Y坐标。
初始化AD和触摸口：
void TouchSrceen_Test(void)

{

rADCDLY = 50000; //(1/3.68MHz)*50000 = 13.56ms
注： 在ADC转换之前用的是外部时钟X-tal clock：3.68MHz
之后才用到GLK: 50MHz

rADCCON = (1<<14)|(prescaler<<6);

注： bit[14]: 0--disable ADC 1--enable ADC bit[13:6]: prescaler = 9 ADC fleq = 50MHz/(9+1) = 5MHz

Uart_Printf("nTouch Screen testn");

rADCTSC = 0xd3;//waiting for interrupt Mode
注： bit[1:0]: 11--waiting for interrupt Mode
bit[2]:0--Normal ADC 1--Auto Sequential measurement of X-position,Y-position
bit[3]:0--XP pull-up enable1--XP pull-up disable
bit[4]: 0--XP output driver enable 1--XP output driver disable
bit[5]: 0--XM output driver disable1--XM output driver enable
bit[6]: 0--YP output driver enable 1--YP output driver disable
bit[7]: 0--YM output driver disable 1--YM output driver enable
bit[8]:0--stylus down interrupt signal 1--stylus up interrupt signal

pISR_ADC = (int)ADC_TCTest;

rINTMSK = ~(1<<31); //clear ADC MASK bit

rINTSUBMSK = ~(1<<9); //clear TouchScreen MASK bit

}

void __irq ADC_TCTest(void)

{

U32 saveADCDLY;

if(rADCDAT0 & 0.8000) //bit[15]:0--stylus down 1--stylus up

{

rADCTSC &= 0xff; //clear bit[8]:0 stylus down 1--stylus up

}

rADCTSC = (1<<3)|(1<<2);//disable XP pull-up

//auto sequential measurement of XY position

saveADCDLY = rADCDLY;

rADCDLY = 40000; //(1/50MHz)*40000=0.8ms
注：如下图，在需要对X,Y转换时切换到GCLK，之前用X-Tal

rADCCON |= 0x01; //start ADC

while(rADCCON & 0x1); //waiting for ADC startup

while(!(rADCCON & 0x8000)); //waiting for ADC end

while(!(rSRCPND & (0x1<<31)));//waiting for interrupt bit=1

xdata = rADCDAT0 & 0x3ff;

ydata = rADCDAT1 & 0x3ff;
注： 读取buffer里的X,Y坐标数据

if(((xdata-xdata_save > 5)||(xdata-xdata_save < -5))

||((ydata-ydata_save > 5)||(ydata-ydata_save < -5)))

{

Uart_Printf("X_value = %d,Y_value = %d,X_data = %d,Y_data = %dn",
xdata,ydata,xdata_save,ydata_save);

}

xdata_save = xdata;

ydata_save = ydata;

rSUBSRCPND |= (1<<9);

rINTSUBMSK =~(1<<9);

rSRCPND |= (0x1<<31);

rINTPND |= (0x1<<31);

rINTMSK = ~(0x1<<31);

注： 清所有跟中断有关的标志位，为下次中断做准备

rADCTSC =0xd3; //waiting for interrupt

rADCTSC |= 0x100;//stylus up

while(!(rSUBSRCPND & (1<<9)));//waiting for stylus up interrupt bit=1

Uart_Printf("The pen has stylus up.");

rSUBSRCPND |= (1<<9);

rINTSUBMSK =~(1<<9);

rSRCPND |= (0x1<<31);

rINTPND |= (0x1<<31);

rINTMSK = ~(0x1<<31);
注： 清所有跟中断有关的标志位，为下次中断做准备

rADCDLY = saveADCDLY;

rADCTSC &= ~0x100; //stylus down

}