当前位置：首页 > 单片机 > 单片机

KS0108 128*64 LCD C语言驱动

时间：2018-07-11 14:30:02
关键字： 128*64    c语言驱动    LCD    ks0108   
手机看文章

扫描二维码
随时随地手机看文章

[导读]/*KS0108 128*64 LCD C语言驱动 参考ICCAVR资料和网上的资料改写 LCD引脚定义 1---GND 2---VCC 3---VLCD 4---D/I 5---R/W 6---E 7到14 D0-D7 15--CS1 16--CS2 17--RESET 18--VEE 19--SW 20--NC */

/*

KS0108 128*64 LCD C语言驱动
参考ICCAVR资料和网上的资料改写
LCD引脚定义
1---GND
2---VCC
3---VLCD
4---D/I
5---R/W
6---E
7到14 D0-D7
15--CS1
16--CS2
17--RESET
18--VEE
19--SW
20--NC
*/
#include
#include
/* 当前行、列存储，行高16点，列宽8点 */
unsigned char CurOffset,CurRow,CurPage,CurCol;
/* 常量定义 */
#define LCD_STATUS_BUSY 0x80 //忙状态
#define START_LINE0 0xc0 //
#define DISPLAY_ON 0x3f //使能
#define DISPLAY_OFF 0x3e //禁止
#define PARA1 0x40 //
//PORTA---数据口 PORTB----控制口
#define LCD_DIR_PORT DDRA
#define LCD_IP_PORT PINA
#define LCD_OP_PORT PORTA
#define LCD_EN_PORT PORTF
#define LCD_CS2_PORT PORTF
#define LCD_CS1_PORT PORTF
#define LCD_RW_PORT PORTF
#define LCD_DI_PORT PORTF
#define LCD_DI_BIT BIT(0)//0x80
#define LCD_RW_BIT BIT(1)//0x40
#define LCD_EN_BIT BIT(2)//0x20
#define LCD_CS1_BIT BIT(3)//0x10
#define LCD_CS2_BIT BIT(4)//0x08
//#define LCD_EN_PORT PORTC
//#define LCD_CS2_PORT PORTC
//#define LCD_CS1_PORT PORTC
//#define LCD_RW_PORT PORTC
//#define LCD_DI_PORT PORTC
//#define LCD_DI_BIT BIT(7)//0x80
//#define LCD_RW_BIT BIT(6)//0x40
//#define LCD_EN_BIT BIT(5)//0x20
//#define LCD_CS1_BIT BIT(4)//0x10
//#define LCD_CS2_BIT BIT(3)//0x08

#define SET_LCD_E LCD_EN_PORT |= LCD_EN_BIT //LCD使能
#define CLEAR_LCD_E LCD_EN_PORT &= ~LCD_EN_BIT //LCD禁止
#define SET_LCD_DATA LCD_DI_PORT |= LCD_DI_BIT //选择指令端口
#define SET_LCD_CMD LCD_DI_PORT &= ~LCD_DI_BIT //选择数据端口
#define SET_LCD_READ LCD_RW_PORT |= LCD_RW_BIT //读模式
#define SET_LCD_WRITE LCD_RW_PORT &= ~LCD_RW_BIT //写模式
#define SET_LCD_CS2 LCD_CS2_PORT |= LCD_CS2_BIT //左屏选择禁止
#define CLEAR_LCD_CS2 LCD_CS2_PORT &= ~LCD_CS2_BIT //左屏选择使能
#define SET_LCD_CS1 LCD_CS1_PORT |= LCD_CS1_BIT //左屏选择禁止
#define CLEAR_LCD_CS1 LCD_CS1_PORT &= ~LCD_CS1_BIT //左屏选择使能
///////////////////////////////////////////////////////////////////
#define LEFT 0
#define RIGHT 1
#define CMD 0
#define DATA 1
///////////////////////////////////////////////////////////////////
//ASCII 字模宽度及高度
#define ASC_CHR_WIDTH 8
#define ASC_CHR_HEIGHT 12
#define ASC_HZ_WIDTH 12
//#define ASC_HZ_HEIGHT 12
typedef struct typFNT_GB16 /*12*16 汉字字模显示数据结构 */
{
char Index[2];
char Msk[24];
};
typedef struct typFNT_ASC16 /* 汉字字模显示数据结构 */
{
char Index[1];
char Msk[16];
};
struct typFNT_ASC16 const ASC_16[] = { /* 显示为8*16 Curier 10 常规*/
"1",0x00,0x00,0x08,0x08,0xFC,0x00,0x00,0x00,0x00,0x00,0x04,0x04,0x07,0x04,0x04,0x00,
"2",0x00,0x00,0x08,0x04,0x84,0x44,0x38,0x00,0x00,0x00,0x06,0x05,0x04,0x04,0x04,0x00,
"3",0x00,0x00,0x08,0x04,0x44,0x44,0xB8,0x00,0x00,0x00,0x02,0x04,0x04,0x04,0x03,0x00,
"4",0x00,0x00,0x80,0x60,0x18,0xFC,0x00,0x00,0x00,0x00,0x01,0x01,0x05,0x07,0x05,0x00,
"5",0x00,0x00,0x7C,0x44,0x44,0x44,0x84,0x00,0x00,0x00,0x02,0x04,0x04,0x04,0x03,0x00,
"6",0x00,0x00,0xF0,0x48,0x44,0x44,0x80,0x00,0x00,0x00,0x03,0x04,0x04,0x04,0x03,0x00,
"7",0x00,0x00,0x0C,0x04,0x84,0x64,0x1C,0x00,0x00,0x00,0x00,0x06,0x01,0x00,0x00,0x00,
"8",0x00,0x00,0xB8,0x44,0x44,0x44,0xB8,0x00,0x00,0x00,0x03,0x04,0x04,0x04,0x03,0x00,
"9",0x00,0x00,0x38,0x44,0x44,0x44,0xF8,0x00,0x00,0x00,0x00,0x04,0x04,0x02,0x01,0x00,
"0",0x00,0x00,0xF8,0x04,0x04,0x04,0xF8,0x00,0x00,0x00,0x03,0x04,0x04,0x04,0x03,0x00,
".",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,0x00,
":",0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x03,0x00,0x00,0x00,
" ",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
"(",0x00,0x00,0x00,0xE0,0x18,0x04,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x10,0x00,0x00,
")",0x00,0x00,0x00,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x00,0x10,0x0C,0x03,0x00,0x00,
};
struct typFNT_GB16 const GB_16[] = { /* 宋体 9小五 显示为12*16 */
"液",0x19,0xE2,0x14,0x42,0xF2,0x2E,0x72,0x8F,0xAA,0x7A,0x02,0x00,0x01,0x07,0x00,0x00,0x07,0x04,0x04,0x02,0x01,0x02,0x04,0x00,
"晶",0x00,0xC0,0x40,0x5F,0xD5,0x15,0xD5,0x55,0x5F,0x40,0xC0,0x00,0x00,0x07,0x05,0x05,0x07,0x00,0x07,0x05,0x05,0x05,0x07,0x00,
"显",0x00,0x40,0x9F,0x15,0xD5,0x15,0xD5,0x15,0x1F,0xC0,0x00,0x00,0x04,0x04,0x05,0x04,0x07,0x04,0x07,0x06,0x05,0x04,0x04,0x00,
"示",0x10,0x12,0x92,0x52,0x12,0xF2,0x12,0x12,0x53,0x92,0x10,0x00,0x02,0x01,0x00,0x04,0x04,0x07,0x00,0x00,0x00,0x00,0x03,0x00,
"的",0xFC,0x44,0x46,0x45,0xFC,0x10,0x2C,0xC7,0x04,0x04,0xFC,0x00,0x07,0x02,0x02,0x02,0x07,0x00,0x00,0x04,0x04,0x04,0x03,0x00,
"第",0x04,0xEA,0xAB,0xAE,0xAA,0xFC,0xAA,0xAB,0xAE,0xBA,0x82,0x00,0x04,0x04,0x02,0x01,0x00,0x07,0x00,0x02,0x02,0x02,0x01,0x00,
"一",0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x30,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
"行",0x48,0x24,0xF3,0x08,0x09,0x09,0x09,0x09,0xF9,0x09,0x08,0x00,0x00,0x00,0x07,0x00,0x00,0x04,0x04,0x04,0x07,0x00,0x00,0x00,
"二",0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x06,0x04,0x00,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x00,
"三",0x00,0x02,0x22,0x22,0x22,0x22,0x22,0x22,0x23,0x02,0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x06,0x04,0x00,
"四",0x00,0xFF,0x81,0x41,0x3F,0x01,0x01,0xFF,0x81,0x81,0xFF,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x07,0x00,
"五",0x00,0x11,0x11,0x91,0x7F,0x11,0x11,0x11,0xF1,0x01,0x00,0x00,0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0x07,0x04,0x04,0x00,
};
void LCD_BUSY(unsigned char lr) //判断忙标志

{
unsigned char status;
CLI();
if(lr==LEFT)
{
CLEAR_LCD_CS2; //cs2=0
SET_LCD_CS1; //cs1=1
}
else
{
SET_LCD_CS2; //cs2=1
CLEAR_LCD_CS1; //cs1=0
}
SET_LCD_CMD;
LCD_DIR_PORT = 0x00;
LCD_OP_PORT = 0xff;
SET_LCD_READ;
SET_LCD_E;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
while((LCD_IP_PORT) & LCD_STATUS_BUSY)
{
CLEAR_LCD_E;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
SET_LCD_E;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
}
CLEAR_LCD_E;
SET_LCD_WRITE;
LCD_OP_PORT = 0xff;
SEI();
}
void write_LCD(unsigned char lr,unsigned char cd,unsigned char data) /*写入指令或数据*/
{
CLI();
LCD_BUSY(lr);
if(cd==CMD)
SET_LCD_CMD;
else
SET_LCD_DATA;
SET_LCD_WRITE;
SET_LCD_E;
LCD_DIR_PORT = 0xff;
LCD_OP_PORT = data;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
CLEAR_LCD_E;
LCD_OP_PORT = 0xff;
SEI();
}
unsigned char read_LCD(unsigned char lr) /* 读显示数据 */
{
unsigned char data;
CLI();
LCD_BUSY(lr);
SET_LCD_DATA;
LCD_DIR_PORT = 0x00;
LCD_OP_PORT = 0xff;
SET_LCD_READ;
SET_LCD_E;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
data=LCD_IP_PORT;
CLEAR_LCD_E;
SET_LCD_WRITE;
LCD_BUSY(lr);
SET_LCD_DATA;
LCD_DIR_PORT = 0x00;
LCD_OP_PORT = 0xff;
SET_LCD_READ;
SET_LCD_E;
asm("nop"); asm("nop");
asm("nop"); asm("nop");
data=LCD_IP_PORT;
CLEAR_LCD_E;

SET_LCD_WRITE;
SEI();
return data;
}
void set_start_line_L(unsigned char line) /*设置显示起始行*/ //0-63
{
write_LCD(LEFT,CMD,0xc0|line);
}
void set_start_line_R(unsigned char line) /*设置显示起始行*/ //0-63
{
write_LCD(RIGHT,CMD,0xc0|line);
}
void set_page_L(unsigned char page) /*设置X地址 设置页*/ //0-7
{
write_LCD(LEFT,CMD,0xb8|page);
}
void set_page_R(unsigned char page) /*设置X地址 设置页*/ //0-7
{
write_LCD(RIGHT,CMD,0xb8|page);
}
void set_col_addr_L(unsigned char col) /*设置Y地址*/ //0-63
{
write_LCD(LEFT,CMD,0x40|col);
}
void set_col_addr_R(unsigned char col) /*设置Y地址*/ //0-63
{
write_LCD(RIGHT,CMD,0x40|col);
}
void init_lcd(void) /*初始化函数*/
{
set_start_line_L(0); /*显示起始行为0*/
set_start_line_R(0); /*显示起始行为0*/
write_LCD(LEFT,CMD,DISPLAY_ON); /* 开显示 */
write_LCD(RIGHT,CMD,DISPLAY_ON); /* 开显示 */
}
void clr_lcd(void) /*清屏函数*/
{
unsigned char pages,i;
for(pages=0;pages<8;pages++)
{
set_page_L(pages); /* X 页地址 */
set_page_R(pages); /* X 页地址 */
for(i=0;i<64;i++)
{
set_col_addr_L(i);//Y
set_col_addr_R(i);//Y
write_LCD(LEFT,DATA,0x0);
write_LCD(RIGHT,DATA,0x0);
}
}
}
/*************************************/
/* 绘点函数 */
/*************************************/
void pixel(unsigned char xx,unsigned char yy,unsigned char flag)
{
unsigned int y,ch;
ch=yy%8; //余数
y=1;
for(;ch!=0;)
{
y=y*2;
ch--;
}
if(xx<64)
{
set_page_L(yy/8);
set_col_addr_L(xx);
ch=read_LCD(LEFT);

set_col_addr_L(xx);
if(flag)
write_LCD(LEFT,DATA,ch|y);
else
{
y=~y;
ch&=y;
write_LCD(LEFT,DATA,ch|y);
}
}
else
{
set_page_R(yy/8);
set_col_addr_R(xx-64);
ch=read_LCD(RIGHT);
set_col_addr_R(xx-64);
if(flag)
write_LCD(RIGHT,DATA,ch|y);
else
{
y=~y;
ch&=y;
write_LCD(RIGHT,DATA,ch|y);
}
}
}
unsigned char GetPage(void) /*得到当前页*/
{
return CurPage;
}
unsigned char GetCol(void) /*得到当前列*/
{
return CurCol;
}
void SetPageCol(unsigned char upage, unsigned char ucol) /* 设置液晶的页和列 */
{
CurPage = upage;
CurCol = ucol;
if(ucol<64)
{
set_page_L(upage);
set_col_addr_L(ucol);
}
else
{
set_page_R(upage);
set_col_addr_R(ucol-64);
}
}
/* 设置当前显示的页和列 */
void SetRowCol(unsigned char urow, unsigned char ucol)
{
unsigned char page;
CurRow = urow;
CurCol = ucol;
switch(urow)
{
case 1:
page=0;
CurOffset=1;
break;
case 2:
page=1;
CurOffset=2;
break;
case 3:
page=3;
CurOffset=1;
break;
case 4:
page=4;
CurOffset=2;
break;
case 5:
page=6;
CurOffset=1;
break;

}
SetPageCol(page,ucol);
}
void disp_char(unsigned char c)
{
unsigned char k,j,uPage,uCol,ch_r,ch_w;
unsigned char width;
unsigned char len;
uPage = GetPage();
uCol = GetCol();
len=sizeof(ASC_16)/sizeof(ASC_16[0]);
for(k=0;k{
if(c == ASC_16[k].Index[0] ) break;
}
if(k{
if(c=='-'||c==':')
width=ASC_CHR_WIDTH-2;
else if(c=='|')
width=ASC_HZ_WIDTH-ASC_CHR_WIDTH;
else
width=ASC_CHR_WIDTH;
if(CurOffset==1) //下半部是写半个字节
{
for(j=0;j{
SetPageCol(uPage,uCol+j);
ch_w=ASC_16[k].Msk[j];
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage+1,uCol);
for(j=0;j{
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) ch_r=read_LCD(LEFT);
else ch_r=read_LCD(RIGHT);
ch_r&=0xf0;
ch_w=ASC_16[k].Msk[ASC_CHR_WIDTH+j]&0x0f;
ch_w|=ch_r;
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
}
else //上半部是写半个字节
{
for(j=0;j{
SetPageCol(uPage,uCol+j);
if(uCol+j<64) ch_r=read_LCD(LEFT);
else ch_r=read_LCD(RIGHT);
ch_r&=0x0f;
ch_w=ASC_16[k].Msk[j];
ch_w=ch_w<<4;
ch_w|=ch_r;
SetPageCol(uPage,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage+1,uCol);
for(j=0;j{
SetPageCol(uPage+1,uCol+j);
ch_r=ASC_16[k].Msk[j];
ch_w=ASC_16[k].Msk[ASC_CHR_WIDTH+j];
ch_r=ch_r>>4;
ch_w=ch_w<<4;
ch_w|=ch_r;
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
}
}
SetPageCol(uPage,uCol+width);
}

void disp_hz(unsigned char const *hz)
{
unsigned char k,j,uPage,uCol,ch_r,ch_w;
uPage = GetPage();
uCol = GetCol();
for(k=0;k{
if(hz[0] == GB_16[k].Index[0] && hz[1] == GB_16[k].Index[1])
break;
}
if(CurOffset==1)
{
for(j=0;j{
SetPageCol(uPage,uCol+j);
ch_w=GB_16[k].Msk[j];
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage+1,uCol);
for(j=0;j{
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) ch_r=read_LCD(LEFT);
else ch_r=read_LCD(RIGHT);
ch_r&=0xf0;
ch_w=GB_16[k].Msk[ASC_HZ_WIDTH+j]&0x0f;
ch_w|=ch_r;
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage,uCol+ASC_HZ_WIDTH);
}
else //汉字上半部是写半个字节
{
for(j=0;j{
SetPageCol(uPage,uCol+j);
if(uCol+j<64) ch_r=read_LCD(LEFT);
else ch_r=read_LCD(RIGHT);
ch_r&=0x0f;
ch_w=GB_16[k].Msk[j];
ch_w=ch_w<<4;
ch_w|=ch_r;
SetPageCol(uPage,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage+1,uCol);
for(j=0;j{
SetPageCol(uPage+1,uCol+j);
ch_r=GB_16[k].Msk[j];
ch_w=GB_16[k].Msk[ASC_HZ_WIDTH+j];
ch_r=ch_r>>4;
ch_w=ch_w<<4;
ch_w|=ch_r;
SetPageCol(uPage+1,uCol+j);
if(uCol+j<64) write_LCD(LEFT,DATA,ch_w);
else write_LCD(RIGHT,DATA,ch_w);
}
SetPageCol(uPage,uCol+ASC_HZ_WIDTH);
}
}
void disp_str(unsigned char const *p)
{
unsigned char i=0;
while(p[i]>0)
{
if(p[i] < 128)
{ /* ASCII */
disp_char(p[i]);
}
else
{ /* 中文 */

disp_hz(&p[i]);
i++;
}
i++;
}
}
void main()
{
unsigned char i;
DDRF = 0xff;
init_lcd();
clr_lcd();
SetRowCol(1,0);
disp_str("液晶显示的第一行1234");
SetRowCol(2,0);
disp_str("液晶显示的第二行2345");
SetRowCol(3,0);
disp_str("液晶显示的第三行3456");
SetRowCol(4,0);
disp_str("液晶显示的第四行5678");
SetRowCol(5,0);
disp_str("液晶显示的第五行6789");
for(i=0;i<64;i++)
pixel(127,i,1);
for(i=0;i<64;i++)
pixel(0,i,1);
for(i=0;i<128;i++)
pixel(i,0,1);
for(i=0;i<128;i++)
pixel(i,63,1);
while(1);
}

来源：互联网

作者：karen

本站声明： 本文章由作者或相关机构授权发布，目的在于传递更多信息，并不代表本站赞同其观点，本站亦不保证或承诺内容真实性等。需要转载请联系该专栏作者，如若文章内容侵犯您的权益，请及时联系本站删除。
换一批
延伸阅读
[通信先锋]

退出LCD三年后：LGD首次向三星转让LCD显示专利

7月29日消息，LG Display已将其在美国的70项LCD液晶显示器相关专利转让给三星显示，值得注意的是，三星显示已于三年前退出LCD业务。

关键字： LCD 三星
[Holtek]

HOLTEK新推出HT16K24整合按键输入的LCD控制驱动IC

HT16K24操作电压为2.4V~5.5V，内建I²C通信接口，提供三种LCD显示与按键模式：24SEG × 4COM + 24 KEY;22SEG × 6COM + 22 KEY;20SEG × 8COM + 20 K...

关键字： LCD MCU 蜂鸣器
[电路设计项目集锦]

构建一个独立的GPS设备

离线GPS工具：跟踪、保存和查找具有距离和方位的航路点——没有网络，没有云，您的数据，您的规则。

关键字： GPS设备 LCD 微控制器 Arduino Uno
[技术前线]

OLED和LCD的区别

在技术上，LCD和OLED各有其独特之处。液晶电视通过控制液态晶体实现图像显示，其原理是在两片玻璃基板中夹入液态晶体，通过细小的电线控制水晶分子的方向。而OLED凭借自发光二极管带来更优的视角与色彩表现，其RGB色彩信号...

关键字： OLED LCD
[电路设计项目集锦]

基于键盘和短信的双门锁系统

双锁系统，通过键盘输入密码开门，客人来了用短信开门

关键字： LCD 双锁系统 L293D 变压器
[ADI]

汽车显示屏——第2部分：TFT LCD、OLED和micro-LED显示屏电源技术

在汽车显示系统领域，TFT LCD显示屏目前是车载显示面板的主流选择。与此同时，OLED和micro-LED显示屏也逐渐吸引了市场的广泛关注。为了适应不同的显示技术，我们需要开发相应的电源技术。TFT LCD显示屏通常使...

关键字： LCD OLED micro-LED
[ADI]

汽车显示屏——第1部分：TFT LCD、OLED和micro-LED显示屏基本原理

如今，汽车行业对先进显示屏的需求空前高涨，亟需能够实现更大尺寸、更高亮度、曲面设计、更高分辨率和更高对比度的解决方案。与此同时，各类新型车载显示屏也日益受到青睐。目前，TFT LCD是汽车平板显示技术的主流选择。OLED...

关键字： LCD OLED micro-LED
[电路设计项目集锦]

如何使用键盘和LCD显示制作一个安全的基于Arduino的门锁

大家好，欢迎回来。在这个项目中，我们将学习如何使用键盘和LCD显示制作一个安全的基于Arduino的门锁。你可以用它来保护你的办公室、房间或家里的保险箱。要锁门和开锁，你需要在安全系统中输入密码。这确保了只有经过授权的人...

关键字： 键盘 LCD Arduino 电子门锁
[TrendForce集邦咨询]

TrendForce集邦咨询：乐金显示广州LCD厂今正式交割，TCL华星光电大世代线产能面积占比将提升至22.9%

April 1, 2025 ---- 乐金显示广州LCD 8.5代线今日(4月1日)正式交割至TCL华星光电，并改名为t11。至此，TCL华星光电将拥有2条6代、4条8.5代、1条8.6代和2条10.5代LCD产线。Tr...

关键字： 电视 PID面板 LCD
[电路设计项目集锦]

将树莓派Pico变成带有触摸屏界面的USB-HID设备

将您的树莓派Pico变成带有触摸屏界面的USB-HID设备!在这个项目中，我们将在Arduino IDE中设置编程环境，为3.5”Pico Touch LCD屏蔽配置库，测试基本功能，创建简单的按钮(用于复制和粘贴)，显...

关键字： 树莓派 触摸屏 LCD Windows
关闭